VALESCO

TECHNOLOGY OF VALESCO

LEADING TECHNOLOGIES
PRODUCTION OF MOTOR VEHICLES
OILS

ТЕХНОЛОГИЯ VHVI

VERY HIGH VISCOSITY INDEX

REQUIRED LEVEL THE QUALITY IS
DETERMINED BY THE FOLLOWING
FACTORS:

RECOMMENDATIONS OF THE AUTOMAKER
(QUALITY LEVEL)

The manufacturer’s recommendations consist in listing the required level of performance properties of oils and, as a rule, in listing properties according to API, ACEA and ILSAC.

TECHNICAL AND ECONOMIC FEASIBILITY

The technical and economic feasibility consists in choosing an oil that will fully meet the requirements of the automaker, and its service life will be as long as possible. And all this at an acceptable cost of oil! In other words, it is necessary to estimate the unit costs per kilometer of mileage.

REQUIRED LEVEL THE QUALITY IS DETERMINED BY THE FOLLOWING FACTORS:

Engine oils, roughly speaking, are a mixture of base oil and additives

MOTOR OIL

Engine oil for engines is divided into 4 groups.
The table provides generalized information on base oils

GROUP I

GROUP II

GROUP III

Common name

Mineral

Mineral

Mineral

Base oil quality category

Low guality

High guality

hydrocracking equipment

Operational indicators, % conД.

100

120

300

Price category, % conl.

100

110

140

From the presented data, it can be seen that the most appropriate,
from a technical and economic point of view, is

use of Group III base oils.

ADDITIVE PACKAGE

The manufacturer’s recommendations consist in listing the required level of performance properties of oils and, as a rule, in listing properties according to API, ACEA and ILSAC.

The additive package gives the base oils additional performance properties

It is necessary to know that additive packages are also different. Their concentration is also important.

Additive packages are not manufactured by any oil manufacturer.

They are purchased from three world leaders in this industry, i.e.

All oil manufacturers purchase additive packages
from the same companies.

ADDITIVE PACKAGE

The base oil has a direct impact on the oil resource, i.e. the inter-service mileage.

The wear of the additive package is an important operational indicator that characterizes the service life of the oil.

IF YOU EXPLAIN WITH AN EXAMPLE, THEN IT LOOKS LIKE THIS:

MOTOR OIL

OIL А

OIL B

OIL C

OIL D

Additive package (price 100 у.е.). Base oils of the Groups I, II, III и IV of price (100, 110, 140, 400 у.е. accordingly).

Group I
and additive package
100+100=200 у.е.

Group II
and additive package
100+110=210 у.е.

Group III
and additive package
100+140=240 у.е.

Group IV
and additive package
100+400=500 у.е.

According to the statistics, the wear
of the additive package when using
these oils under the same conditions will be:

8 000 km

11 000 km

15 000 km

18 000 km

The calculation of technical feasibility
is carried out according to the ratio
of mileage costs:

200 у.е/8 000 km = 25,0 у.е./1000 km

210 у.е/11 000 km = 19,1 у.е./1000 km

240 у.е/15 000 km = 16,0 у.е./1000 km

500 у.е/18 000 km = 27,7 у.е./1000 km

ADVANTAGES OF VALESCO
OVER COMPETITORS

Motor oils of high quality levels cannot be obtained on a mineral basis.

Most modern oils are developed on the basis of Group III oils. However, most of the leading oil producers do not have their own capacities for the production of Group III oils

ABSOLUTE LEADER
FOR THE PRODUCTION OF SYNTHETIC MOTOR OILS OF GROUP III

sells these oils to the world’s leading brands.

It uses its own Group III engine oils for the production of VALESCO oils. This has a positive effect on the quality and cost of the oil

COST PRICE
ENGINE OIL

(manufacturer or buyer).

COST OF THE ADDITIVE PACKAGE

(approximately the same for all leading companies).

STONKS

(approximately the same for all leading companies).

ADDED VALUE

mark-up for the brand
(the more well-known the brand, the higher the margin).